How do I reset UniFi AP to factory defaults?

How do I reset UniFi AP to factory defaults?

Physical Reset

  1. Press and hold the reset button for 10 seconds while AP is connected.
  2. Release the button (the LEDs on the UAP will stop glowing).
  3. Do not disconnect the UAP from its power source during the reboot process.
  4. The UAP will restore factory settings.

How do I reset my Ubiquiti AP?

Remove the LAN cable or PoE injector to stop the power supply to the access point and then re-connect the cable. This process will reboot the access point. Unplug and re-plug the Ethernet cable and it will reboot the access point. Each access point can be rebooted in the same way.

What is the default password for UniFi AP?

As long as the UniFi Access Point has not been previously setup or adopted by the software, and only if you are attempting to connect via SSH, then always use the default username and password of ubnt / ubnt.

How do I factory reset my Ubiquiti AP Pro?

Reset This button serves two functions for the UniFi AP-PRO: • Restart Press and release the Reset button quickly. Restore to Factory Default Settings Press and hold the Reset button for more then five seconds.

How do you reset your computer to factory?

Navigate to Settings > Update & Security > Recovery. You should see a title that says “Reset this PC.” Click Get Started. You can either select Keep My Files or Remove Everything. The former resets your options to default and removes uninstalled apps, like browsers, but keeps your data intact.

How do I reboot my access point?

Unplug the access point’s power cable and wait for 30 seconds then plug it back in. Wait for the access point’s lights to appear solid. NOTE: Make sure to press and hold the Reset button properly. The lights on the access point should be blinking while you are holding the Reset button.

How do I reset UniFi Network?

Reset Button This button serves two functions for the UniFi Switch: • Press and release the Reset button to restart the device. Press and hold the Reset button (for at least five seconds) to restore the device to its factory default settings.

How do I reset my UAP AC Pro?

What is the default IP address for UniFi AP?
If you didn’t know, Ubiquiti Access Points have a default IP address of 192.168. 1.20.

Can’t connect to UniFi AP?

Make sure the access points aren’t rebooting In some cases, connectivity issues might be caused by UniFi Access Points rebooting. To make sure this isn’t the case, check the uptime of you APs: Log into UniFi Network. On the Devices tab, select the AP.

How to reset an unifi AP?

Go to Settings > Maintenance > Restore > Click Choose File button.

  • The file will load and you will be asked to confirm you wish to restore that backup.
  • Once you confirm,the backup restoration will begin. This process takes a few minutes,do not disconnect while the Controller is working on this.
  • How to install unifi AP?

    Unpack and Connect. I won’t go into detail too much about the actual placement of the Access Point,the Unifi Access Points come with a perfectly clear

  • Download the Unifi Controller Software. We are going to install the Unifi Controller to manage our access points.
  • Install Unifi Controller.
  • How to fix Ubiquiti unifi AP in disconnect status?

    Pinged the AP and it is pingable

  • SSH to the AP via Putty and login with the credentials mentioned above
  • Issued the command few times but no luck. AP is still showing as disconnected.
  • Since I was not on-site,I issued the command reboot and that resolved the issue. I was able to finish updating the AP’s firmware.
  • How to reset unifi controller?

    – Log in to the UniFi Network Controller. In the Devices page, click on the UAP you wish to reset. – Select the Configuration tab, and click Manage Device to expand. – Click the Forget button. This will erase all configuration and history for that device, effectively resetting it.

    Begin typing your search term above and press enter to search. Press ESC to cancel.

    Back To Top